MOUSETRAP
Slippery and jumping onto you will take him outside now just a click off the side and remove the bottle and really so what you're gonna need for this project is eighteen and a half inches a two-by-four a two liter pop bottle coat hanger and three screws and three washers use a knife and take the label off the ball first fill up a bottle of hot water and this will come right off and if you wanna take up the city he said just use wd-40 the good thing about this most rappers you'll be able to use this bottle over and over again just have to put a bit more beaten there and you're good to go to Cuba support and cut off the end at the two and a half inch mark and cut straight piece off the bottom of the ninth inning and the remaining piece cut at five inches longer of the two pieces this is really popular going to slide on you just take a file and rounded out with.
If you don't have a file just use sandpaper now market off of the one-inch parking ticket pair of pliers and blended into a loop then measure from the other end to five inches and bending angle. Something like that that's not quite perfect just use your hands and bent it. Take a shorter piece and Mark one inch from each and do the same and been a loop in both ends. Then once you've done that way to the center and then a 90 degree angle take a pencil and put the pop bottle on top of the pencil find the balancing point of the ball now measure it and make a mark on the opposite side of the ball now make a mark quarter inch ahead of where you made the works as we want the front end to be later in the back in to be a bit heavier and you want to put an identifying mark on the one side of the bottle so that you know that the bottle has a slight on at the shop the same way each time the drill bit that is slightly bigger than a coat hanger and make mark the five and a half inch mark and put it right in the center now take your bigger angle peace and fitted underneath the washer and now at this point you'll see that this one is . this way a little bit just take your hand and push it over until it's pretty well ninety degrees. You want to make sure that it's sitting parallel to the surface here to just take it on bended until it is take your bottle in the side view mark with the circle it's always going to go on the shaft outweigh sliding on at the very bottom between the bottle and the two-by-four you want to have a half an inch gap undo the screw this is fully adjustable you can move up and down and you can get it just perfect the block and at the one-inch mark put in another screw and washer and then take our small bracket that we've bent and fit underneath the washer and tighten the screw down once the bracket with bottom of the template for the last room washer make a marketing intern at quarter end and put the last one in and take our blocking shit underneath this group can bring close to the bottle and snuggle so this is our final adjustment is really easy to do take the bottle and just tilted down and you'll notice the bottle is not perfectly parallel to the block here now because we've used coat hanger here it's nice and soft we can bend that so just take the block and play with it just been to back a bit if you've gone too far just bend forward and to just go back and forth until you get it just right until is perfectly parallel with the bottle then just go to our school back here and loosen it off and then tilter bottle down and what you want to do is just move the block ahead until it just almost touches the ball you touching the ball you wanna not to touch it you can push this up and down and once you're satisfied there's not touching at all just tighten the screw down now you may have to do this a few times that's just perfect right there and the last thing you want to do is find yourself close p.m. People clan or paper clip that holds the bottom lines now just get yourself a little bit of peanut butter on the end your finger and put it just on the inside the neck of the bottle there so he could smell it and he'll go right in .
If you don't have a file just use sandpaper now market off of the one-inch parking ticket pair of pliers and blended into a loop then measure from the other end to five inches and bending angle. Something like that that's not quite perfect just use your hands and bent it. Take a shorter piece and Mark one inch from each and do the same and been a loop in both ends. Then once you've done that way to the center and then a 90 degree angle take a pencil and put the pop bottle on top of the pencil find the balancing point of the ball now measure it and make a mark on the opposite side of the ball now make a mark quarter inch ahead of where you made the works as we want the front end to be later in the back in to be a bit heavier and you want to put an identifying mark on the one side of the bottle so that you know that the bottle has a slight on at the shop the same way each time the drill bit that is slightly bigger than a coat hanger and make mark the five and a half inch mark and put it right in the center now take your bigger angle peace and fitted underneath the washer and now at this point you'll see that this one is . this way a little bit just take your hand and push it over until it's pretty well ninety degrees. You want to make sure that it's sitting parallel to the surface here to just take it on bended until it is take your bottle in the side view mark with the circle it's always going to go on the shaft outweigh sliding on at the very bottom between the bottle and the two-by-four you want to have a half an inch gap undo the screw this is fully adjustable you can move up and down and you can get it just perfect the block and at the one-inch mark put in another screw and washer and then take our small bracket that we've bent and fit underneath the washer and tighten the screw down once the bracket with bottom of the template for the last room washer make a marketing intern at quarter end and put the last one in and take our blocking shit underneath this group can bring close to the bottle and snuggle so this is our final adjustment is really easy to do take the bottle and just tilted down and you'll notice the bottle is not perfectly parallel to the block here now because we've used coat hanger here it's nice and soft we can bend that so just take the block and play with it just been to back a bit if you've gone too far just bend forward and to just go back and forth until you get it just right until is perfectly parallel with the bottle then just go to our school back here and loosen it off and then tilter bottle down and what you want to do is just move the block ahead until it just almost touches the ball you touching the ball you wanna not to touch it you can push this up and down and once you're satisfied there's not touching at all just tighten the screw down now you may have to do this a few times that's just perfect right there and the last thing you want to do is find yourself close p.m. People clan or paper clip that holds the bottom lines now just get yourself a little bit of peanut butter on the end your finger and put it just on the inside the neck of the bottle there so he could smell it and he'll go right in .
No comments:
Post a Comment